Flue-gas-analyzer

Flue-gas-analyzer-FGA08   download


  • Fully integrated system Up to 7 gases in a single compact analyser
  • Wide measurement range
  • From 0 -100 PPM up to 0 -10,000 PPM
  • Widely accepted, certified performance
  • Complies with the latest monitoring standards
  • Simple installation & maintenance
  • Requires no specialist skills or training,
  • all maintenance carried out on-site
  • Highest measurement perlumidnce
  • Ultra - low drift measurement technology
  • Measured Total NOx (NO+N02) Separate sensors for Lrue NOx monitoring,
  • Record and store vital emission data
  • Internal data logging function
  • Combustion efficiency measurement option
  • For a Optimization process efficiency where condition are changing

The Model 7001 is a Rugged, Portable, Easy-to-use Gas Analyser that monitors purge gases and the cooling gas in hydrogen-cooled turbine generators. It measures hydrogen in air & hydrogen in C02 as well as C02 in air during maintenance purging of hydrogen rooted turbine generators. Switch selectable ranges on the instrument make it easytochoosethe measurement required.

Technique Advanced Dual Sensor Technology
Optional Single Sensor Technology
IR/UV Sensor Technology
Resolution 0-1 ppm (CO, NO, No2, & S02); 0.1% (Co2)
Linearity <2% of range
Zero drift <2% of range per month
Span drift <2% of range per month
02 Ranges 0-5 Vol% to 0-25 Vol%
Resolution 0.01 Vol%
Linearity <0.2 Vol%
Zero drift *0.2 Vol% per month
Span drift <0.2 Vol% per month
Calibration method Manual or Automatic 2-Point calibration span and zero automatic gas selection (option)
Display Type Alpha numeric LCD back light
Analogue outputs Isolated current loops One per gas 4-20 mA
Relays outputs One per gas
Relay rating Isolated changeover contacts rated 0.5A @ 125V a.c; V d.c
Communications RS 232 or R5 485 Modbus serial digital data bus (2 or 4 wire)
Enclosure 19" Rack
Operating Temp 40deg C to + 50deg C
Power consumption 400 w
Instrument air (0 calibration) 4 bar/ 60 psi min. clean dry & solvent free; 10 1/min
Calibration gas (recommended) 1 bar/15 psi; 2L/min approx
Calibration gas type Specific to each gas type & measurement span
Dimensions (H x W x D) < 20 seconds
Response Time 1570x600x370 mm
Options 24x24x12 mm

The above Parameter and Ranges are only indicative. Endee will build up and supply the analyser with Parameters, range and features to any Practical Configuration.

Note : Specifications and Features will vary with application. The above are established and validated during design, but are not to be construed as test criteria for every product. Due to endee's commitment to research, design and product improvement, specifications are subject to change without notice

3 Reviews

  1. 5.00 out of 5
    Lorem ipsum dolor sit amet, consectetur adipiscing elit. Quisque sit amet venenatis orci, ut tempus ipsum. Donec sit amet massa et dui ultricies eleifend. Curabitur at nibh ante.
  2. 5.00 out of 5
    Lorem ipsum dolor sit amet, consectetur adipiscing elit. Quisque sit amet venenatis orci, ut tempus ipsum. Donec sit amet massa et dui ultricies eleifend. Curabitur at nibh ante.
  3. 3.00 out of 5
    Lorem ipsum dolor sit amet, consectetur adipiscing elit. Quisque sit amet venenatis orci, ut tempus ipsum. Donec sit amet massa et dui ultricies eleifend. Curabitur at nibh ante.

Add a review